DISCOVERING ESSENTIAL PLUMBING SKILLS IS VITAL FOR BATHTUB INSTALLATION

Discovering Essential Plumbing Skills is Vital for Bathtub Installation

Discovering Essential Plumbing Skills is Vital for Bathtub Installation

Blog Article

Details Here

We've stumbled upon this great article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the web and thought it made sense to discuss it with you in this article.


A Step-by-Step Guide to Installing a Bathtub
Mounting a tub isn't specifically rocket science, yet it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a moderately challenging project. If the old bathtub is conveniently available, the job can move quickly; if you have to open up a wall to remove the old bathtub and also position the new bathtub, the job is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub and also embeded in the brand-new one. Make sure you have actually certified on your own for the task as well as fit attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is better to think about utilizing one before you begin. Chances are you might need a professional plumber to make tube links.
This write-up will certainly help you set up a new tub in your shower room if you have already gotten a new tub and also do not require to alter the arrangement of your previous water supply pipelines.
Your devices and material checklist should make up the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, turn on the taps to drain any water continuing to be in the system. The procedure of removing the existing faucets can be fairly bothersome because of the restricted gain access to that is often the situation.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipes. When the supply pipes have actually been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning throughout this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
    Prior to proceeding to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.

    Fitting New Taps


    If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipelines.
    If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next, position the tap in the installing hole in the bath/basin making certain that the washers are in area in between the faucet as well as the sink. Safeguard the tap in position with the producer provided backnut. Once the faucet is safely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former kind needs to be attached to the faucet ends first, tightening just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.

    Setting up the Bath tub


    Using the two wooden boards under its feet, position the bathtub in the called for setting. The wooden boards are handy in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto four tiny factors.
    The next objective is to make sure that the tub is leveled all round. This can be achieved by inspecting the spirit level and also changing the feet on the bathtub till the spirit level reads degree.
    To set up faucets, fit the bottom of the furthest versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other tap.
    Switch on the water supply and examine all joints and new pipework for leaks and tighten them if needed. Load the bath tub and also examine the overflow electrical outlet as well as the typical outlet for leaks.
    Ultimately, fix the bathroom paneling as defined in the manufacturer's user's manual. Tiling and securing around the bathtub should wait up until the bathtub has actually been utilized at the very least once as this will certainly resolve it into its final position.

    Getting ready for the Setup


    To start with, the supporting framework provided with the bathroom should be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to stop pressure on the bath tub.
    Fit the flexible faucet ports to the bottom of both faucets using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you utilize all of the provided washers.
    Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its final setting.

    Tiling Around the Tub


    In the area where the bath satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to break an inflexible seal, creating the water to permeate the wall surface in between the bath and also the tiling, causing problems with dampness as well as possible leaks to the ceiling below.
    You can select from a selection of coloured sealers to assimilate your components and also fittings. They are offered in tubes and also cartridges, and are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the bathtub with water before securing, to allow for the activity experienced when the tub is in use. The sealant can split relatively early if you do not consider this motion before securing.
    Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    As a passionate person who reads on Tools You Need to Install a New Bathtub , I was thinking sharing that short article was a good idea. Sharing is caring. Helping others is fun. We cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    For true quality, dial!

    Report this page